Problem 1234

Can you please specify what version of Geant4 you're using ?
Also, there is no attachment uploaded to this report. It is therefore impossible for us to make any investigation.
Can you please provide the missing information ?
The warning you get from G4MaterialPropertyVector is likely uncorrelated to a geometry problem and eventually associated to the optical physics setup of the application...

Created attachment 130 [details]
tar.gz that contains main.cc macro src.tar and include.tar

>Can you please specify what version of Geant4 you're using ?

4.9.3

>Also, there is no attachment uploaded to this report. It is therefore
>impossible for us to make any investigation

Sorry, I don't find any "upload" button in my bugzilla account. May I send to you an email?

>The warning you get from G4MaterialPropertyVector is likely uncorrelated to a
>geometry problem and eventually associated to the optical physics setup of the
>application.

The example that I made for bugzilla is a simplification of my complete setup.

Perhaps, it is better to upload (or email) the tar.gz of my complete setup.

Is it possible?

Created attachment 131 [details]
tar.gz cointains a complete MC. During run I have: G4Exception : Notification       issued by : G4Paraboloid::DistanceToIn(p,v) Point p is inside!

This MC runs ok with al lot of warnings:


*** G4Exception : Notification
      issued by : G4Paraboloid::DistanceToIn(p,v)
Point p is inside!
*** This is just a warning message.
WARNING - G4Paraboloid::DistanceToIn(p,v)
          p = (30.76042335,0.5739114165,-21.63727978) mm
          v = (0.7561243347,-0.2456864795,0.6065592669) mm

Setup: A black box (made of Plexi and inside Air)that contains:
1) Lead Glass (for Cerenkov)
2) Dummy Detector (air)
3) A Mirror inside a Cylinder
4) Detector (little box) at the bottom of Lead Glass

Outside of BlackBox there is a box (Plexi) simulating a BuildUp material

testcomplete.in is the macro. 
1000 gamma impinging LeadGlass, then Cerenkov Optical Photons to the Mirror.

Dear Sergio,

Unfortunately, I'm not able to run your complete application.
I have a segmentation fault comming from HistoManager::ScoreNewTrack ().

Could you check if the attachment is complete and 
if the attached application is working ?

Best Regards,
Tatiana Nikitina

Created attachment 132 [details]
Complete tar.gz (after a second check and make clean) It's ok on my PC. No segmentation fault.

I have made a “make clean” and then “make”

Then, I run with: /home/g4/bin/Linux-g++/TestComplete /home/lomeo/TestComplete/testcomplete.in

In attach the complete tar.gz

This is the final summary: 

many warnings as:

*** G4Exception : Notification
      issued by : G4Paraboloid::DistanceToIn(p,v)
Point p is inside!
*** This is just a warning message.
 Total Number of Optical Photons (Cerenkov) in Target: 0
 Total Number of Optical Photons (Scintillation): 0
RunAction: End of run actions are started
HistoManager: End of run actions are started

then the summary:
========================================================
Beam particle                        gamma
Beam Energy(MeV)                     4.24546
Number of events                     1000
Average energy deposit (MeV)         0.6236   RMS(MeV) 0.9309
Average number of steps              238.8
Average number of gamma              0.72
Average number of e-                 48.71
Average number of e+                 0.036
Average number of neutrons           0
Average number of protons            0
Average number of antiprotons        0
Average number of pi+ & pi-          0
Average number of pi0                0
Average number of kaons              0
Average number of muons              0
Average number of deuterons+tritons  0
Average number of He3+alpha          0
Average number of ions               0
Average number of forward neutrons   0
Average number of reflected neutrons 0
Average number of leaked neutrons    0
Average number of proton leak        0
Average number of pion leak          0
Average number of optical photos (T) 31.34
========================================================

and it’s ok, no segmentation.

Dear Sergio,

 Thank you for this new version, it is working for me.
 I will investigate these warning messages from G4Paraboloid.

 I have tested your application on the possible overlaps using 
 G4PVPlacement(...,last paramter=true). There is No overlaps detected.
 You can have a look in Application Developers Guide, Chapter 4, 
 to see more details about different tools to detect overlaps. 
 In any case I will also investigate if the problem reported by 'geometry/test'
 is a real problem of the Solid or Not.

 Best Regards,

 Tatiana

Created attachment 133 [details]
Fix for G4Paraboloid

Dear Sergio,

 The raison for Warnings from DistanceToIn(p,v) is found.
 There was an error in G4Paraboloid::DistanceToIn(p).
 In attachment you will find the fix for geant4.9.3 version.

 Could you try it out and tell if it is works for you also?

 Best Regards,

 Tatiana

Created attachment 134 [details]
Fix for 9.3 version 

This second version is a fix for error messages from /geometry/test/recursive_test

Dear Sergio,

 The problem reported by /geometry/test/recursive_test was fixed.
 I have included fix for geant4.9.3 version. This fix will be also included in next geant4 release.

Thank you for your help,
Best Regards,

Tatiana